HW7 Prop-R-Vent(sku: HW7)
HW7 fall away Prop-R-Vent kit for top-loading kilns.
Help us to make sure we send you the right part and enter the model number and serial number of the kiln for which you need this part:
Kiln Sitter Cone Supports, KS-2(sku: KS-2)
Insert the cone supports into the slots in the Kiln Sitter porcelain tube. Package of 2.
Release Claw for Kiln Sitter(sku: RELEASECLAW)
Release Claw for the Dawson Kiln Sitter and the Orton Auto-Cone. Fits all sensing rods. Instructions included.
Timer Motor(sku: TIMERMOTOR)
Motor for the Limit Timer on the Dawson Kiln Sitter and the Orton Auto-Cone. 208 - 240 volt, 60 hertz.
HW4 Small Lid Handle(sku: 1001)
Lid handle for small kilns, 8 sides or less.
KS7 Kiln Sitter Tube Assembly(sku: 4041)
KS7 Dawson Kiln Sitter or Orton Auto-Cone Tube Assembly for the Paragon S and SnF series kilns. The replacement tube assembly may not look exactly the same as the original, because we have changed manufacturers. Do not be concerned; the tube assembly will still fit.
PL2 Peephole Plug Cone Shaped(sku: 2000)
PL2 Peephole plug, cone shaped. Keep a spare on hand in case you drop one. The plug is essential for kilns equipped with a downdraft vent.
BP7 Full Formed Steel Base, 7 Sided Kilns(sku: 3054)
The full-formed steel base for 7-sided kilns. The base is made of long-lasting galvanized steel. It protects the firebrick kiln bottom. Install the steel base by removing the old one and sliding the tabs of the new one up behind the stainless steel case. Then fasten with screws.
SW6 Infinite Control Switch, 240V(sku: 4151)
Infinite control switch, 240 volt. The switch cycles the elements on and off. The higher the switch setting, the longer the elements stay on with each cycle. on High, the elements stay on continuously. (Note: If you are replacing a Duncan KM300 switch with the SW6, the switch must be installed upside-down. --Thank you)
KN7 Knob with Pointer(sku: 4204)
KN7 Knob with Pointer (for S and SnF series Paragon kilns). Black plastic with white pointer.
MS1 Porcelain Insulators(sku: MS1)
MS1 Porcelain Insulators, 1 1/8" long (28.57 mm). 4 per package. The insulators prevent the element from touching the kiln case.
MS6 Element Connectors(sku: MS6)
MS6 Element Connectors, brass, 2 per package. Use new connectors when replacing an element. (Note: Paragon replacement elements come with new connectors.)
VENTMAST120, Not Installed(sku: VENTMAST120)
The patented Orton Vent Master not only vents fumes but also improves firing results.
It pulls fresh oxygen into the kiln for brighter colors, especially noticeable with red and orange glazes and decals. Fire red and green glazes in the same load without glaze contamination. The Vent Master draws air from the kiln, dilutes it with room air, and pushes it outdoors through a vent hose.
The extra oxygen and increased air movement help burn carbon out of the clay, which helps eliminate a host of firing problems: bloating, dark patches in the clay, porcelain mildew, pinholes, pitting, blisters, and bubbles.
The Vent Master removes fumes containing volatile metals, fluorides and sulphur oxides. You can fire even lusters, decals, metallics, and pate-de-verre glass without strong odor.
The flow of fresh air helps even out the temperature throughout the kiln. The vent also extends the life of the Kiln Sitter tube assembly, since fumes by-pass the tube.
You will enjoy the convenience of the Vent Master. Throughout the firing, keep the lid closed and peephole plugs inserted. You no longer need to remember to lower the hot lid from vented position.
The Vent Master increases firing time by about five minutes for firings up to cone 4; 12 minutes for firings from cone 4 to 10. It has little effect on maximum temperature. At 132 watts, electrical consumption of the Vent Master motor is only pennies per firing.
From the shut-off temperature down to 1000°F, the Vent Master has little effect on cooling time. From 1000°F to room temperature, it reduces cooling time by about two hours.
As with Paragon kilns, the Orton Vent Master can be made for any electrical system in the world. Approved for use in the 1992 Uniform Mechanical Code. UL/CSA approved for UL Listed kilns. ETL Listed, CE Certified. Two year limited warranty.
The Vent Master requires a separate 120 volt wall plug unless your kiln is equipped with the AOP vent.
A 3’ long 2” duct comes with each vent. The 2” duct runs between the collection cup and the blower motor. Use 4” aluminum dryer duct or 4” PVC pipe between the motor and the vent outlet. (Do not use vinyl dryer duct.)
Position the Vent Master next to the kiln and attach the collection cup to the bottom or side of the kiln. The collection cup fits under most top-loading kilns. (Note: The kiln stand must be at least 5” high to accommodate the collection cup.) Since the vent motor is away from the kiln, there is no vibration in the kiln, the motor is kept away from the heat of the kiln, and the fan is easy to clean. The Vent Master works with all Paragon kilns except the smallest tabletop models. The Vent Master can vent two kilns. For the second kiln, order the Vent Master Expansion Kit.
Shipping dimensions: 15" wide x 10" deep x 12" high.
Rolling Stand Replacement Part, 18x18x12 inches(sku: SKU STD181812-BA)
The replacement stand for your Paragon 7- and 8-sided top-loading ceramic kiln has locking casters, a mounting bracket for the Orton Kiln Vent, and a greenware drying rack. (Take advantage of the heat that radiates from the kiln. Load greenware onto the lower shelf. Heat from the kiln will dry the ware for the next firing.) Roll the kiln out of the way when not using it. Ships unassembled. Assembly instructions included. This deluxe stand replaces the discontinued standard kiln stand. 18” square x 12” high. Ships in a 20” x 25” x 7” carton.
ELEMENT S663, 240 VOLTS, 5 OHMS, 2 PER KILN
The element comes pre-stretched and bent at the wallbrick corners for a precise fit. Element connectors are included with each new element.
ELEMENT S663, MIDDLE, 240 VOLTS, 3 OHMS, 2 PER KILN
CORDSET, 20 AMP, 240 VOLT, NEMA 6-20, 6 FOOT
PLASTIC FEET FOR KILN STAND
PILOT LIGHT with push-on terminals.
STRAIGHT, 2 GROOVE BRICK, 7 SIDE, 2.5" BRICK When ordering bricks, always specify the Paragon kiln model number, which is listed on the kiln's safety data plate.
PLAIN, NO GROOVE HALF BRICK, 7 SIDE, 2.5" BRICK When ordering firebricks, always specify the Paragon kiln model number, which is listed on the kiln's safety data plate.
BRICK BOTTOM FOR 66B, 66B3
LID FOR 66B, 66SB, 77B. The lid comes with a band, but it does not include hardware such as the hinge and handle.
Paragon Industries, L.P.,
2011 South Town East Blvd.
Mesquite, Texas 75149-1122
Copyright © 2020,Paragon Industries, L.P.
“Custom and standard Kilns and Industrial Furnaces for ceramics, pottery, heat treating, enameling,dentistry, laboratory, and glass fusing.Better Designed Kilns from Paragon Industries!"