TF5 Half Amp Fuse(sku: 6726)
TF5 Half Amp Fuse, AGC, 250V AC. This fuse protects the digital controller. The fuse is mounted in the kiln's control panel (usually on the side of the kiln).
Help us to make sure we send you the right part and enter the model number and serial number of the kiln for which you need this part:
Caldera Top/Bottom(sku: BRCalderaTB)
The Caldera top and bottom are interchangeable. Lift off the damaged top or bottom and slide on the new one. Includes the stainless steel band with tighteners and two handles. Fully assembled. (BR Caldera TB)
Caldera Top with 2 inch x 2 inch Glass Window(sku: CAL-DR-W-1)
Order a separate firebrick top with 2” x 2” high-temperature window for a Caldera that you already own. It installs in minutes.
Watch the bright red kiln interior through the window. (The glass is rated to 2300°F.) This is especially convenient for glass fusing. Watch your glass treasures progress through every stage from tack fuse to full fuse. (Note: always wear firing safety glasses when viewing the kiln interior.)
Note: The Caldera will not reach its maximum temperature when equipped with the glass window. To reach maximum temperature, fire the Caldera with the plain lid.
CS RM 15A 240V 6-15P 14-3 6FT
ELEMENT, CALDERA, 240V, 17.1 OHM, 2 PER KILN
The element comes pre-stretched for a precise fit. Element connectors are included with each new element.
MS1 Porcelain Insulators(sku: MS1)
MS1 Porcelain Insulators, 1 1/8" long (28.57 mm). 4 per package. The insulators prevent the element from touching the kiln case.
MS6 Element Connectors(sku: MS6)
MS6 Element Connectors, brass, 2 per package. Use new connectors when replacing an element. (Note: Paragon replacement elements come with new connectors.)
TF9 Fuse Holder for Switch Box of Digital Kilns(sku: TF9)
Fuse Holder for the kiln's AGC half amp fuse. The fuse holder is built into the kiln control panel (usually located on the side of the kiln).
PY80-4 Thermocouple (PY50)(sku: 6750-14)
Thermocouple (temperature sensor), K-type, 1/4” diameter, exposed tip 14-gauge complete with ceramic block and lead wires for 2 1/2” - 3” wall kilns. (Order the PY81-4 if you do not need to replace the ceramic block or lead wires.) Our beaded thermocouple with polished tip is rugged and reliable. The thermocouple is made in the U.S. with American-made components to exacting standards. The “special limit” thermocouple wire is certified to be close tolerance.
SSP CONTROLLER SENTRY XPRESS CONE 10/2400F
HW4 Small Lid Handle(sku: 1001)
Lid handle for small kilns, 8 sides or less.
Caldera Steel Stand(sku: 34740-23)
The original Caldera and Caldera-S kilns were placed on top of four firebrick blocks. The Calderas now come with a 2 1/2" high x 14" x 12 3/4" (63 mm high x 355 mm x 323 mm) steel stand, complete with mar-proof rubber feet.
PY81-4 Thermocouple, K-Type, 2.5-3 inch Wall Kilns(sku: 60179-4)
Thermocouple (temperature sensor), K-type, 1/4” diameter, exposed tip 14-gauge for 2 1/2” - 3” wall kilns (less ceramic block and wires). Our beaded thermocouple with polished tip is rugged and reliable. The thermocouple is made in the U.S. with American-made components to exacting standards. The “special limit” thermocouple wire is certified to be close tolerance.
TF72 Sentry Xpress Control Cable(sku: 6060-2)
TF72 Sentry Xpress Control Cable
TF3 Relay 30 Amp(sku: 6355)
Relay, 30 amp, 12 volt coil. The relay sends power to the elements of digital kilns.
Paragon Industries, L.P.,
2011 South Town East Blvd.
Mesquite, Texas 75149-1122
Copyright © 2020,Paragon Industries, L.P.
“Custom and standard Kilns and Industrial Furnaces for ceramics, pottery, heat treating, enameling,dentistry, laboratory, and glass fusing.Better Designed Kilns from Paragon Industries!"